Biomaterials Advances

Journal: Biomaterials Advances

Abbreviation

Biomater Adv

Publisher

Elsevier

ISSN

2772-9508
2772-9516

Show all metadata

Search Results

Publications 1 - 10 of 22

In-vitro investigation of endothelial monolayer retention on an inflow VAD cannula inside a beating heart phantom
Magkoutas, Konstantinos; Chala, Nafsika; Wu, Xi; et al. (2023)
Biomaterials Advances
Ventricular assist devices (VADs) provide an alternative solution to heart transplantation for patients with end-stage heart failure. Insufficient hemocompatibility of VAD components can result in severe adverse events, such as thromboembolic stroke, and readmissions. To enhance VAD hemocompatibility, and avoid thrombus formation, surface modification techniques and endothelialization strategies are employed. In this work, a free form patterning topography is selected to facilitate the endothelialization of the outer surface of the inflow cannula (IC) of a commercial VAD. An endothelialization protocol for convoluted surfaces such as the IC is produced, and the retainment of the endothelial cell (EC) monolayer is evaluated. To allow this evaluation, a dedicated experimental setup is developed to simulate realistic flow phenomena inside an artificial, beating heart phantom with a VAD implanted on its apex. The procedural steps of mounting the system result to the impairment of the EC monolayer, which is further compromised by the developed flow and pressure conditions, as well as by the contact with the moving inner structures of the heart phantom. Importantly, the EC monolayer is better maintained in the lower part of the IC, which is more susceptible to thrombus formation and may therefore aid in minimizing the hemocompatibility related adverse events after the VAD implantation.
Bioresorbable, amorphous magnesium-fiber reinforced bone cement with enhanced mechanical and biological properties
Rich, Andrea M.; Berger, Leopold; Deller, Robin; et al. (2025)
Biomaterials Advances
In this study, we developed and characterized a fully biodegradable composite bone cement reinforced with short, randomly oriented amorphous magnesium fibers. Fibers of composition Mg60Zn35Ca5 (in at.%) with 50 μm diameter and 2 mm length were produced by wire spinning and then mixed with a magnesium calcium phosphate cement using fiber volume fractions between 10 and 20 %. The interface strength between the fibers and cement was improved by treating the fibers with diammonium hydrogen phosphate. Compared to the reference cement without fibers, flexural strength was increased by 18 % for the composites with 13 and 18 vol% fibers, and the work of fracture was increased by over 1000× in all cases (p < 0.05, n = 6). Immersion in simulated body fluid for two and four weeks showed that the cement's struvite phase degrades first, and overall, the composite degrades slower. The degradation rate can be tailored to the application by changing the fiber percentage or the cement/fiber composition. Murine pre-osteoblastic cells (MC3T3) cultured in extracts of reference and composite cements had significantly higher cell viability, and composites with 13 vol% fibers also had a significantly higher number of cells compared to the control, indicating that the fibers can enhance and promote pre-osteoblastic cell growth. The results demonstrate that amorphous magnesium fibers enhance both the mechanical and biological properties of ceramic bone cement, expanding their prospects for clinical application.
A novel bistable device to study mechanosensitive cell responses to instantaneous stretch
Choi, Young; Morlino, Giulia; Toboso-Navasa, Aparo; et al. (2022)
Biomaterials Advances
The behavior of cells and tissues in vivo is determined by the integration of multiple biochemical and mechanical signals. Of the mechanical signals, stretch has been studied for decades and shown to contribute to pathophysiological processes. Several different stretch devices have been developed for in vitro investigations of cell stretch. In this work, we describe a new 3D-printed uniaxial stretching device for studying cell response to rapid deformation. The device is a bistable compliant mechanism holding two equilibrium states—an unstretched and stretched configuration—without the need of an external actuator. Furthermore, it allows multiple simultaneous measurements of different levels of stretch on a single substrate and is compatible with standard immunofluorescence imaging of fixed cells as well as live-cell imaging. To demonstrate the effectiveness of the device to stretch cells, a test case using aligned myotubes is presented. Leveraging material area changes associated with deformation of the substrate, changes in nuclei density provided evidence of affine deformation between cells and substrate. Furthermore, intranuclear deformations were also assessed and shown to deform non-affinely. As a proof-of-principle of the use of the device for mechanobiological studies, we uniaxially stretched aligned healthy and dystrophic myotubes that displayed different passive mechanical responses, consistent with previous literature in the field. We also identified a new feature in the mechanoresponse of dystrophic myotubes, which is of potential interest for identifying the diseased cells based on a quick mechanical readout. While some applications of the device for elucidating passive mechanical responses are demonstrated, the simplicity of the device allows it to be potentially used for other modes of deformation with little modifications.
Variations in fluid chemical potential induce fibroblast mechano-response in 3D hydrogels
Garau Paganella, Lorenza; Badolato, Asia; Labouesse, Celine; et al. (2024)
Biomaterials Advances
Mechanical deformation of skin creates variations in fluid chemical potential, leading to local changes in hydrostatic and osmotic pressure, whose effects on mechanobiology remain poorly understood. To study these effects, we investigate the specific influences of hydrostatic and osmotic pressure on primary human dermal fibroblasts in three-dimensional hydrogel culture models. Cyclic hydrostatic pressure and hyperosmotic stress enhanced the percentage of cells expressing the proliferation marker Ki67 in both collagen and PEG-based hydrogels. Osmotic pressure also activated the p38 MAPK stress response pathway and increased the expression of the osmoresponsive genes PRSS35 and NFAT5. When cells were cultured in two-dimension (2D), no change in proliferation was observed with either hydrostatic or osmotic pressure. Furthermore, basal, and osmotic pressure-induced expression of osmoresponsive genes differed in 2D culture versus 3D hydrogels, highlighting the role of dimensionality in skin cell mechanotransduction and stressing the importance of 3D tissue-like models that better replicate in vivo conditions. Overall, these results indicate that fluid chemical potential changes affect dermal fibroblast mechanobiology, which has implications for skin function and for tissue regeneration strategies.
Effect of molecular weight of tyramine-modified hyaluronan on polarization state of THP-1 and peripheral blood mononuclear cells-derived macrophages
Wychowaniec, Jacek K.; Bektas, Ezgi Irem; Vernengo, Andrea J.; et al. (2025)
Biomaterials Advances
The immunomodulatory properties of hyaluronan and its derivatives are key to their use in medicine and tissue engineering. In this work we evaluated the capability of soluble tyramine-modified hyaluronan (THA) synthesized from hyaluronan of two molecular weights (low Mw = 280 kDa and high Mw = 1640 kDa) for polarization of THP-1 and peripheral blood mononuclear cells (PBMCs)-derived macrophages (MΦs). We demonstrate the polarization effects of the supplemented THA by flow cytometry and bead-based multiplex immunoassay for the THP-1 derived MΦs and by semi-automated image analysis from confocal microscopy, immunofluorescent staining utilizing CD68 and CD206 surface markers, RT-qPCR gene expression analysis, as well as using the enzyme-linked immunosorbent assay (ELISA) for PBMCs-derived MΦs. Our data indicate that supplementation with LMW THA drives changes in THP-1 derived MΦs towards a pro-inflammatory M1-like phenotype, whereas supplementation with the HMW THA leads to a more mixed profile with some features of both M1 and M2 phenotypes, suggesting either a heterogeneous population or a transitional state. For cells directly sourced from human patients, PMBCs-derived MΦs, results exhibit a higher degree of variability, pointing out a differential regulation of factors including IL-10 and CD206 between the two cell sources. While human primary cells add to the clinical relevance, donor diversity introduces wider variability in the dataset, preventing drawing strong conclusions. Nevertheless, the MΦs profiles observed in THP-1 derived cells for treatments with LMW and HMW THA are generally consistent with what might be expected for the treatment with non-modified hyaluronans of respective molecular weights, confirming the known association holds true for the chemically tyramine-modified hyaluronan. We stipulate that these responses will provide basis for more accurate in vivo representation and translational immunomodulatory guidance for the use of THA-based biomaterials to a wider biomaterials and tissue engineering communities.
Control of hydrostatic pressure and osmotic stress in 3D cell culture for mechanobiological studies
Kourouklis, Andreas P.; Wahlsten, Adam; Stracuzzi, Alberto; et al. (2023)
Biomaterials Advances
Hydrostatic pressure (HP) and osmotic stress (OS) play an important role in various biological processes, such as cell proliferation and differentiation. In contrast to canonical mechanical signals transmitted through the anchoring points of the cells with the extracellular matrix, the physical and molecular mechanisms that transduce HP and OS into cellular functions remain elusive. Three-dimensional cell cultures show great promise to replicate physiologically relevant signals in well-defined host bioreactors with the goal of shedding light on hidden aspects of the mechanobiology of HP and OS. This review starts by introducing prevalent mechanisms for the generation of HP and OS signals in biological tissues that are subject to pathophysiological mechanical loading. We then revisit various mechanisms in the mechanotransduction of HP and OS, and describe the current state of the art in bioreactors and biomaterials for the control of the corresponding physical signals.
Patient's dermal fibroblasts as disease markers for visceral myopathy
Viti, Federica; Pramotton, Francesca Micaela; Martufi, Michela; et al. (2023)
Biomaterials Advances
Visceral myopathy (VSCM) is a rare genetic disease, orphan of pharmacological therapy. VSCM diagnosis is not always straightforward due to symptomatology similarities with mitochondrial or neuronal forms of intestinal pseudo-obstruction. The most prevalent form of VSCM is associates with variants in the gene ACTG2, encoding the protein gamma-2 actin. Overall, VSCM is a mechano-biological disorder, in which different genetic variants lead to similar alterations to the contractile phenotype of enteric smooth muscles, resulting in the emergence of life-threatening symptoms. In this work we analyzed the morpho-mechanical phenotype of human dermal fibroblasts from patients affected with VSCM, demonstrating that they retain a clear signature of the disease when compared with different controls. We evaluated several biophysical traits of fibroblasts, and we show that a measure of cellular traction forces can be used as a non-specific biomarker of the disease. We propose that a simple assay based on traction forces could be designed to provide a valuable support for clinical decision or pre-clinical research.
Multi-doped apatite: Strontium, magnesium, gallium and zinc ions synergistically affect osteogenic stimulation in human mesenchymal cells important for bone tissue engineering
Vukomanović, Marija; Gazvoda, Lea; Anicic, Nemanja; et al. (2022)
Biomaterials Advances
Functional calcium phosphate biomaterials can be designed as carriers of a balanced mixture of biologically relevant ions able to target critical processes in bone regeneration. They hold the potential to use mechanisms very similar to growth factors naturally produced during fracture healing, while circumventing some of their drawbacks. Here we present a novel phase of carbonated-apatite containing Mg2+, Sr2+, Zn2+ and Ga3+ ions (HApMgSrZnGa). While all dopants decrease the crystallinity, Ga3+ limits crystal growth and enables the formation of a nanosized apatite phase with enhanced specific surface area. Coexistence of the ions enhances degradability and controls solubility of low crystalline, distorted, multi-doped apatite structure, controlled by Ga3+ ions accumulated at the surface. Consequently, HApMgSrZnGa supports the viability of human mesenchymal stromal cells (MSCs) and induces their stimulation along the osteogenic lineage. In addition, the co-released ions has a synergistic antimicrobial effect, particularly within the HApMgSrZnGa-Au(arg) composite with Au(arg) as contact-based antimicrobial. The activity is stable up to two months in vitro. Osteogenic nature and antimicrobial activity, combined in a single biomaterial, are suggesting a well-balanced, multi-doped apatite design applicable as future option in bone regeneration and tissue engineering.
The combined effect of zinc and calcium on the biodegradation of ultrahigh-purity magnesium implants
Okutan, Begüm; Schwarze, Uwe Y.; Berger, Leopold; et al. (2023)
Biomaterials Advances
Magnesium (Mg)-based implants are promising candidates for orthopedic interventions, because of their biocompatibility, good mechanical features, and ability to degrade completely in the body, eliminating the need for an additional removal surgery. In the present study, we synthesized and investigated two Mg-based materials, ultrahigh-purity ZX00 (Mg–Zn–Ca; <0.5 wt% Zn and <0.5 wt% Ca, in wt%; Fe-content <1 ppm) and ultrahigh-purity Mg (XHP-Mg, >99.999 wt% Mg; Fe-content <1 ppm), in vitro and in vivo in juvenile healthy rats to clarify the effect of the alloying elements Zn and Ca on mechanical properties, microstructure, cytocompatibility and degradation rate. Potential differences in bone formation and bone in-growth were also assessed and compared with state-of-the-art non-degradable titanium (Ti)-implanted, sham-operated, and control (non-intervention) groups, using micro-computed tomography, histology and scanning electron microscopy. At 6 and 24 weeks after implantation, serum alkaline phosphatase (ALP), calcium (Ca), and Mg level were measured and bone marrow stromal cells (BMSCs) were isolated for real-time PCR analysis. Results show that ZX00 implants have smaller grain size and superior mechanical properties than XHP-Mg, and that both reveal good biocompatibility in cytocompatibilty tests. ZX00 homogenously degraded with an increased gas accumulation 12 and 24 weeks after implantation, whereas XHP-Mg exhibited higher gas accumulation already at 2 weeks. Serum ALP, Ca, and Mg levels were comparable among all groups and both Mg-based implants led to similar relative expression levels of Alp, Runx2, and Bmp-2 genes at weeks 6 and 24. Histologically, Mg-based implants are superior for new bone tissue formation and bone in-growth compared to Ti implants. Furthermore, by tracking the sequence of multicolor fluorochrome labels, we observed higher mineral apposition rate at week 2 in both Mg-based implants compared to the control groups. Our findings suggest that (i) ZX00 and XHP-Mg support bone formation and remodeling, (ii) both Mg-based implants are superior to Ti implants in terms of new bone tissue formation and osseointegration, and (iii) ZX00 is more favorable due to its lower degradation rate and moderate gas accumulation.
In-situ-forming zwitterionic hydrogel does not ameliorate osteoarthritis in vivo, despite protective effects ex vivo
Asadikorayem, Maryam; Weber, Patrick; Zhang, Shipin; et al. (2025)
Biomaterials Advances
Osteoarthritis (OA) is one of the most common degenerative joint diseases, with no effective therapeutic options available. In this study, we aimed to develop an interpenetrating, in-situ-forming hydrogel based on biocompatible and anti-fouling zwitterionic (ZI) polymers for early-stage OA treatment. We hypothesized that the anti-fouling properties of zwitterions could provide tissue protection, and the high charge density of these polymers would enhance tissue penetration and lubrication. The hydrogel comprises carboxybetaine acrylamide as the ZI backbone and tyramine acrylamide as a functional comonomer to enable enzymatic and tissue-adhesive crosslinking. The hydrogel demonstrated exceptional tissue penetration and long-term retention in bovine cartilage explants. Moreover, hydrogel application protected cartilage in inflammatory media, enhanced lubrication, and decreased permeability. However, ZI hydrogel injection in collagenase-induced osteoarthritis model in rats did not prevent cartilage degeneration, and similar levels of tissue degradation and surface roughness were observed in rats injected with the ZI hydrogel and in OA controls. Additionally, ZI polymer without in-situ crosslinking resulted in increased cartilage degradation compared to both hydrogel and OA control. Furthermore, synovial tissue inflammation and significantly increased immune cell infiltration were observed in response to ZI materials. This study highlights the potential immunogenicity effect of ZI polymers in our disease model, contributing to impaired protective effects as well as exacerbated degeneration.

Publications 1 - 10 of 22

Journal: Biomaterials Advances

Abbreviation

Publisher

Journal Volumes

ISSN

Description

Filters

Search Results