Renate List

Last Name

List

First Name

Renate

ORCID

0000-0003-3292-1915

Organisational unit

01630 - Lehre HEST

Show all metadata

Search Results

Publications 1 - 5 of 5

Impact of Surgical Alignment, Bone Properties, Anterior-Posterior Translation, and Implant Design Factors on Fixation in Cementless Unicompartmental Knee Arthroplasty
Yang, Huizhou; Marras, Daniele; Clary, Chadd W.; et al. (2025)
Journal of Biomechanical Engineering
Micromotion exceeding 150 μm at the implant-bone interface may prevent bone formation and limit fixation after cementless knee arthroplasty. Understanding the critical parameters impacting micromotion is required for optimal implant design and clinical performance. However, few studies have focused on unicompartmental knee arthroplasty (UKA). This study assessed the impacts of alignment, surgical, and design factors on implant-bone micromotions for a novel cementless UKA design during a series of simulated daily activities. Three finite element models that were validated for predicting micromotion of cementless total knee arthroplasty (TKA) were loaded with design-specific kinematics/loading to simulate gait (GT), deep knee bending (DKB), and stair descent (SD). The implant-bone micromotion and the porous surface area ideal for bone ingrowth were estimated and compared to quantify the impact of each factor. Overall, the peak tray-bone micromotions were consistently found at the lateral aspect of the tibial baseplate and were consistently higher than the femoral micromotions. The femoral micromotion was insensitive to almost all the factors studied, and the porous area favorable for bone ingrowth was no less than 93%. For a medial uni, implanting the tray 1 mm medially or the femoral component 1 mm laterally reduced the tibial micromotion by 19.3% and 26.3%, respectively. Differences in tray-bone micromotion due to bone moduli were up to 59.8%. A 5 mm more posterior femoral translation increased the tray-bone micromotion by 35.8%. The presence of the tray keel prevented the spread of the micromotion and increased the overall porous surface area, but also increased peak micromotion. The tray peg and the femoral anterior peg had little impact on the micromotion of their respective implants. In conclusion, centralizing the load transfer to minimize tibial tray applied moment and optimizing the fixation features to minimize micromotion are consistent themes for improving cementless fixation in UKA. Perturbation of femoral-bone alignment may be preferred as it would not create under/overhang on the tibia.
Using Video-Fluoroscopy and Multibody Modelling to Unveil the Influence of a Gradually Reducing Femoral Radius on Ligament Elongation Patterns Following Posterior Cruciate-Retaining Total Knee Arthroplasty
Hosseini Nasab, Seyyed Hamed; Bänteli, Philipp; List, Renate (2024)
Applied Sciences
Stability in total knee arthroplasties (TKAs) is mainly provided by soft tissue structures and the implant geometry. Paradoxical anterior translation could be decreased with a gradually reducing femoral radius compared to a dual-radii design. However, the influence of the sagittal curvature of the femoral condyles on knee ligaments remains unclear. This study quantified the length change patterns of the medial and lateral collateral ligaments (MCL and LCL) and posterior cruciate ligament (PCL) in 15 subjects with a gradually reducing radius and 15 subjects with a dual-radii TKA. Kinematics obtained from video-fluoroscopy were used to drive personalised multibody knee models. The ligament lengths were analysed throughout complete cycles of level gait, stair descent, and sit-to-stand-to-sit activity. Regardless of the implant design, our results indicated flexion-dependent elongation patterns in all ligament bundles. Importantly, however, subjects with the dual-radii implant design exhibited higher ligament strains during the mid-flexion phase compared to those with gradually reducing designs. Our findings, therefore, emphasise the importance of the impact of subtle changes in implant geometry on the loading patterns of the knee soft tissues, which need to be acknowledged by implant manufacturers and orthopaedic surgeons.
In Vitro Verification of Simulated Daily Activities Using Implant-Specific Kinematics from In Vivo Measurements
Behnam, Yashar A.; Krishnan, Ahilan Anantha; List, Renate; et al. (2024)
Bioengineering
The mechanism and boundary conditions used to drive experimental joint simulators have historically adopted standardized profiles developed from healthy, non-total knee arthroplasty (TKA) patients. The purpose of this study was to use implant-specific in vivo knee kinematics to generate physiologically relevant boundary conditions used in the evaluation of cadaveric knees post-TKA. Implant-specific boundary conditions were generated by combining in vivo fluoroscopic kinematics, musculoskeletal modeling-generated quadriceps loading, and telemetric knee compressive loading during activities of daily living (ADL) to dynamically drive a servo-hydraulic knee joint simulator. Ten cadaveric knees were implanted with the same TKA components and mounted in the knee simulator to verify the resulting load profiles against reported fluoroscopic kinematics and loading captured by an ultra-congruent telemetric knee implant. The cadaveric simulations resulted in implant-specific boundary conditions, which accurately recreate the in vivo performance of the like-implanted knee, with Root Mean Square Error (RMSE) in femoral low point kinematics below 2.0 mm across multiple activities of daily living. This study demonstrates the viability of in vivo fluoroscopy as the source of relevant boundary conditions for a novel knee loading apparatus, enabling dynamic cadaveric knee loading that aligns with clinical observations to improve the preclinical development of TKA component design.
Biomechanical effects of foot orthoses during walking
Stacoff, Alex; Kramers-de Querbain, Inès; Dettwyler, Markus; et al. (2007)
The Foot
The purpose of this study was to quantify kinetic and kinematic effects during the stance phase of walking using three different foot orthoses. All test subjects were measured under five test conditions with 10 repetitions each. The test conditions included: neutral orthosis (tested twice) and three different orthoses (posting, molding and posting combined, proprioceptive). Whereas most previous studies rely on healthy subjects to describe effects of orthoses during gait, the present study used eight patients (all pes valgus). Standard gait analysis was used with force plates (KISTLER) and an optoelectric measuring system (VICON). The results show that the combined molding and posting foot orthosis significantly reduced eversion and eversion moments during walking compared to a posting type and a proprioceptive orthosis in several test parameters. EMG measurements with fine wire electrodes on three of the test subjects revealed that the activity pattern of the tibialis posterior muscle can considerably change between subjects but may not be used to explain apparent individual effects. The results suggest that for subjects with pes valgus a combined molding and posting orthoses reduces eversion best and that individual variations may be due to subject dependent proprioception, internal foot mechanics and/or a combination of both.
The role of limb alignment on natural tibiofemoral kinematics and kinetics
Postolka, Barbara; Taylor, William R.; Fucentese, Sandro F.; et al. (2024)
Bone & Joint Research
Aims This study aimed to analyze kinematics and kinetics of the tibiofemoral joint in healthy subjects with valgus, neutral, and varus limb alignment throughout multiple gait activities using dynamic videofluoroscopy. Methods Five subjects with valgus, 12 with neutral, and ten with varus limb alignment were assessed during multiple complete cycles of level walking, downhill walking, and stair descent using a combination of dynamic videofluoroscopy, ground reaction force plates, and optical motion capture. Following 2D/3D registration, tibiofemoral kinematics and kinetics were compared between the three limb alignment groups. Results No significant differences for the rotational or translational patterns between the different limb alignment groups were found for level walking, downhill walking, or stair descent. Neutral and varus aligned subjects showed a mean centre of rotation located on the medial condyle for the loaded stance phase of all three gait activities. Valgus alignment, however, resulted in a centrally located centre of rotation for level and downhill walking, but a more medial centre of rotation during stair descent. Knee adduction/abduction moments were significantly influenced by limb alignment, with an increasing knee adduction moment from valgus through neutral to varus. Conclusion Limb alignment was not reflected in the condylar kinematics, but did significantly affect the knee adduction moment. Variations in frontal plane limb alignment seem not to be a main modulator of condylar kinematics. The presented data provide insights into the influence of anatomical parameters on tibiofemoral kinematics and kinetics towards enhancing clinical decision-making and surgical restoration of natural knee joint motion and loading.

Publications 1 - 5 of 5

Renate List

Last Name

First Name

ORCID

Organisational unit

Filters

Search Results